• Home
  • Products
  • Applications
  • Support
  • Find Parts
  • Contact Us
Home > Support > Repair Specifications
Engine Model 
Documents and Manuals
Governors Special Tools
Repair Specifications
Standard Cyclinder Bore3.0005 - 2.9995
Piston Skirt to Bore Clearance.003 - .0035 Cam Ground
.0045 - .005 Split Skirt
Crankpin Diameter1.126 - 1.255
Connecting Rod to Crankpin Clearance.0007 - .002
.0011 - .003 Shell Bearing to Crankpin Clearance (Vertical)
Valve Tappet Clearance - Cold/Inlet.008
Valve Tappet Clearance - Cold/Exhaust.016
Bolt Torque Specifications(FT. LBS.)
Connecting Rod20
Cylinder Block/Center Main to C.CaseNone
Cylinder Head32
Engine Base9
Gear CoverNone
Manifold9
Main Bearing Plate22
Spark Plug30
Flywheel80
Rope SheaveNone
Additional Specifications(FT. LBS.)
Crankcase Old Capacity3 PTS
Running Spark Advance20 Degrees
Maximum Engine Operating R.P.M.3600
Emission CertifiedFalse
Maintenance Specs
1.  Every 4 to 8 hours check air cleaner and clean or replace.
2.  Every 8 hours check crankcase oil level.
3.  Every 50 drain crankcase and refill with fresh oil.
4.  For gasoline engines use only regular grade gasoline(87 Octane Min.)
Crankcase, Crankshaft and Main Bearing Common Specs
1.  Cylinders Worn .005" or more over Standard Size, Rebore, Hone and Fit with Oversize Piston and Rings.
2.  Crankshaft End Play: .002 to .005" (Cold), (W2-1230, W2-1235, W2-1250, .005 to .012)
3.  W2-1230, W2-1235 & W2-1250 Main Bearing Clearance: .002 to .005"-Connecting Rod Side Clearnance .009 - .018" - Piston Ring End Gap .010 to .020.
4.  W4-1770 3rd Bearing Housing to Crankcase Torque 40-45 Foot Pounds.
Piston Common Specs
1.  Piston Pin to Piston: .0000 to .0008" Tight(W2-1230, W2-1235 & W2-1250 = .0005 TO .0008 Loose)
2.  Piston Pin to Connecting Rod: .0005 to .001" (ACN, BKN, S7D, H8D, TR10D, TRA12D = .0002 TO .0008)(W2-1230, W2-1235 & W2-1250 = .0006 TO .0015 Tight)
Ignition Common Specs
1.  Spark Advance Check for Distributor/Ignition Timers: Engine must be running at 2000 RPM or above.
2.  Breaker Point Gap: Distributor = .020", Magneto = .015".
3.  Timing for Models S7D, HS7D, S8D, S10D, S12D, S14D, TR10D AND TRA10D is set by adjusting breaker point gap, preferrably with a continuity light or ohmmeter. For correct procedure see "TIMING" section in repair manuals
4.  Breakerless Ignition (not adjustable): standard on TRA12D, optional on S10D, S12D & S14D.
5.  Spark Plug Gap = .030".
Valves Common Specs
1.  Valve Face and Valve Seat Angle: 45 Degrees
2.  Valve stem to guide clearance: .003 to .005" for all models except: ACN-BKN, V460D, V461D, V465D, VR4D=.002 TO .004". Exhaust only - S7D, HS7D, S8D, HS8D, TR10D, TRA10D, TRA12D = .002 TO .004" (W2-1230 = .003 to .005") Inlet Only - S7D, HS7D, S8D, HS8D, S10D, S12D, S14D, TR10D, TRA10D, TRA12D, W2-1230 = .001 to .003"
3.  When Clearance Becomes .002" Over Hight limit, Replace guides.

Headquarters

10 Industrial Drive
Dyer, Tennessee
Fax: 731-665-6116
Home | Products | Applications | Support | Distributors | Contact Us

Thank you for visiting Wisconsin Engines, LLC on the internet. We build gasoline, LP and NG fueled, air-cooled and water-cooled engines. Our product offering ranges from 9hp to 72hp . Our unique product offering, addresses a specific and valuable niche in the market place.